Easy Steps in How to Fix a Sagging Gate

How to Fix a Sagging Gate

We all know how much of a burden a dragging gate can turn to be. For this reason, today we’ll give you the main steps in how to fix a sagging gate. 

It’s normal for gates to droop, especially if they’re old. Time and gravity can make your gate unaligned with the gate post support. Luckily, there’s no need to replace your gate. As a matter of fact, you can fix your drooping gate under $15!

All you need to do is follow these simple instructions. So keep on reading to learn how to stop a gate from sagging.

5 Main Steps in How to Fix a Sagging Gate

First, it’s important that for this project, you need to get yourself an anti-age gate kit. These kits are the perfect gate sag eliminator. Not only will they bring the necessary materials for the job, but also they’re affordable as well. The materials they bring are:

  • 1 Cable
  • 1 Turnbuckle
  • 2 Cable clamp
  • 2 Metal corner brackets

Although these kits work for almost all types of gates,  be sure to check out the cable’s length. It must be the same length as your gate’s diagonal length. Also, keep in mind that these repair kits work best with small and medium-sized gates. 

When it comes to much larger gates, it’s best to call a professional. 

Besides your reliable anti-age gate kit, you’ll also need:

  • Drill
  • Screws
  • Slip joint pliers or adjustable wrench
  • Wirecutter (Optional)
  • Screwdriver (Optional)

The steps in how to fix a sagging gate are:

  1. Install the upper corner bracket to the gate’s hinge side. 
  2. Run cable through remaining bracket and attach one cable clamp.
  3. Install lower corner bracket to the gate’s latch side.
  4. Loosen turnbuckle and place it on the upper corner.
  5. Run cable through turnbuckle and attach the other cable clamp.
  6. Adjusting turnbuckle.

Below, we’ll go over each of these steps:

Install Upper Corner Bracket to the Gate’s Hinge Side

Each repair kit counts on two brackets: one for the upper part of the gate and the lower part. Start by taking one of these brackets and placing it at the upper part of the gate. Remember to place the bracket on the gate’s hinge side. 

When making the pilot holes, feel free to use a pencil to mark the holes’ positions. 

Additionally, when counting on an old wooden gate, be sure to make the screw holes slightly angled. That way, the bracket will be able to get a good grip from the gate. Also, when drilling, make sure that the holes are the manufacturer’s recommended size.

Run Cable Through Remaining Bracket and Attach One Cable Clamp

Before placing the bottom bracket, you must first do two things, running the cable through the bracket and attaching the cable to one cable clamp. This will help you save both time and effort since it’s more difficult running the cable once you installed the bracket.

After threading the cable through the bracket, you can loop it back for the cable clamp. Place the looped cable on the clamp in a way that both cables sit beside each other, with the clamp’s bolt between them. 

After that, proceed into tightening the clamp with either slip-joint pliers or an adjustable wrench.

Install Lower Corner Bracket to the Gate’s Latch Side

After threading the cable through the remaining bracket, it’s time to attach it to the bottom of the gate. When installing the lower corner bracket, you need to attach it to the latch side of the gate.

Loosen Turnbuckle and Place It on the Upper Corner

With both corner brackets placed, you’ll need to loosen up the turnbuckle as much as you can. Loosen until both bolts are almost completely unscrewed. Then, you’ll proceed with placing it on the upper corner bracket’s eye.

Run Cable Through Turnbuckle and Attach the Other Cable Clamp

Following placing the turnbuckle in the upper bracket, you can loop the other side of the cable through the turnbuckle. 

Just like you did with the lower corner bracket, you’ll have to place both cables alongside, with the clamp’s bolt in between. However, before securing the clamp, make sure to tighten the cable as much as possible. 

Also, if you can, try to lift up the gate by placing something beneath it, such as a wooden board. This will help make the tightening less difficult.

After tightening the cable, continue by securing the clamp just like you did with the other clamp. Lastly, if you wish, you can use wire cutters to trim off the excess cable.

Adjusting Turnbuckle

Last but not least, you’ll need to adjust the turnbuckle. When tightening the turnbuckle, feel free to use your screwdriver for a much easier process. 

By the end, after tightening the turnbuckle, you should have a gate that’s sag-free!

How to Keep a Wooden Gate from Sagging?

First, keep in mind that gates sag as time passes. After all, when opening a gate, you pull against the post and the hinges, In other words, you place extra weight that ultimately causes gates to droop.

Gates are more prone to sag when hinges aren’t placed correctly, as well as when the gate’s material becomes deformed.

Also, it’s important to keep in mind:

  • Wooden gates sag more compared to metal gates.
  • Low-quality wooden gates sag much more than high-quality wooden gates.
  • Gates without diagonal bracing structure sag more.
  • Posts need to be sunken low enough to withstand the gate’s weight.

In order to prevent your gate from sagging, you must first know the reason why it’s sagging in the first place. For instance, if your gate is sagging because the post isn’t deep enough, then you should consider getting an expert to fix the gate’s post.

In most cases, you can keep a gate from sagging using the kit we mentioned previously in this article.

When Should I Call a Professional?

Gate repair can be either easy or extremely complex. As stated beforehand in this article, anti-sag repair kits work best for gates that are small and medium-sized. Whenever you’re counting on a larger drooped gate, it’s best to call an expert gate repair service. 

Want to know the top reasons to install an automatic gate opener? Click here to learn more!